Prova S1The slide that keeps its own record.

When a stain is questioned, pull up the slide’s history: the heat, time and handling your patients’ tissue went through, from water bath to scan.

Reserve S1Order V1, get an S1 demo kit

Prova S1: a glass microscope slide with a dark sensing end and a violet light at the seam

A question for your lab

How long did this slide wait between the dryer and the stainer?

Not the rack. Not the run. Slide S1-0264.

Where would you look for the answer today?

The answer

12minutes.

5 min over the example lab’s limit

In this example the transfer ran from 09:51 to 10:03, five minutes past the lab’s seven-minute review limit. The rack simply waited.

The slide recorded it anyway: when it left the dryer, when it reached the stainer, and how warm it was the whole time in between.

One slide, three answers

That was one question. The slide answers three.

Heat

How hot did it get?

95.0°C

Peak recorded temperature, during the 40-minute cell-conditioning step. Measured at the slide.

Time

How long did it wait?

12min

Dryer to stainer. Five minutes past the example lab’s limit of seven.

Handling

What happened on the way?

2.4g

Peak recorded acceleration, at 13:56. Operator note: rack set down before coverslipping.

Heat, time and handling, kept with the one slide they happened to.

Illustrative record excerpt · S1-0264

Reserve S1 for your lab.

Free, with no obligation to order. Or order V1 and get an S1 demo kit.

Your lab records what’s on the slide. S1 records what happened to it.

Images, reports, LIS fields and instrument logs tell part of the story. S1 adds the slide’s own record of temperature, elapsed time and handling.

Already in your records

  • Slide images
  • Pathology reports
  • LIS fields
  • Instrument logs

S1 adds

  • Temperature measured on the slide
  • Timestamped readings
  • Recorded movement and impacts
  • An append-only record stored on the slide

Capture what you can’t see.

A protocol says what should happen. S1 records what did, at the slide, on every run.

The label end of a Prova S1 slide, sealed, with one fine violet line where it meets the glass.

Inside S1

How it keeps its own record.

Sensors sealed inside the label end. The record stays with the slide from water bath to scan. Tap your phone to read it.

01Handling

0.19g

Steady. Peak over the last 30 minutes, on three axes.

02Temperature

60.0°C

In spec, 58 to 62 °C. 1.0 °C spread across three sensor points.

03Record

214entries

Append-only. Slide S1-0264. Stored on the slide, read with a compatible phone.

  1. Drying started
  2. Mounting started

04Time

00:19:41

Step 3 of 7, drying. Every reading carries its own timestamp.

Once the slide is stained, its history is gone. S1 keeps it.

Illustrative values. Not yet for sale. In development.

One slide. Every step, measured.

  1. The slide awakens.

    Recording starts. S1-0264, case P-2048.

  2. Breast core needle biopsy mounts.

    38 s on the water. Three serial sections, one ribbon.

  3. The heat it saw, and for how long.

    30 min, upright, nothing touching the sections.

  4. Five minutes past the lab’s 7-minute limit.

    The rack waited. The slide counted every minute, at 22.4 °C.

  5. Every heated step of this run.

    First puddle, sealed under liquid coverslip.

  6. Heat retrieval, every degree on the record.

    40 min at the run’s peak temperature.

  7. One drop. The test itself.

    HER2 primary antibody, 16 min.

  8. Brown, where HER2 is.

    The chromogen develops on the cores, nowhere else.

  9. Blue for everything else.

    Every step of the run, timed and on the record.

  10. Handled, counted, time-stamped.

    after 1 h 27 min in the queue · 2.4 g at 13:56, rack set down

  11. It arrives with its whole day.

    on the record · 214 entries · ready to read with a tap

The Prova Record™

When a result is questioned, bring the slide’s record.

Every S1 read can be exported as a Prova Record: one document your QA lead can open, review and keep.

Record™Illustrative · 12 Nov 2026
S1-0264
Case
P-2048
Assay
HER2 IHC
On record
09:06 to 14:14
On record
5 h 08 min
Peak heat
95.0 °C
Peak knock
2.4 g
To review
1 interval
  1. WokeRecording starts
    21.0 °C
  2. Tissue mountedFlotation bath
    45.1 °C38 s
  3. DryingSlide dryer
    59.8 °C30 min
  4. Transfer5 min over · limit 7 minDryer to stainer
    22.4 °C12 min
  5. StainingStainer · cell conditioning 40 min
    peak 95.0 °C2 h 28 min
  6. QueueBefore coverslipping
    22.8 °C1 h 27 min
  7. AccelerationOperator note: rack set down
    2.4 g
  8. CoverslippingCoverslipper · 6 moves
    23.6 °C16 min
  9. ScannedScanner · record closed

Reviewer’s note · Transfer 09:51 to 10:03

Rack held while the instrument was prepared.

J. Smith, Histology Supervisor
Reviewed 14:32

Selected events from 214 entries · written as it happened, on the slideLimit from this lab’s settings: transfer 7 min
  1. 01
    Which slide, which case

    Slide ID, case and assay, carried on every page of the record.

  2. 02
    Every step

    Start time, duration and the temperature measured at the slide.

  3. 03
    Your limits, beside the reading

    The thresholds come from your lab’s settings, and the record shows which were crossed.

  4. 04
    Recorded movement

    Movement and acceleration events, each with the time it happened.

  5. 05
    Who reviewed it

    The reviewer’s name and note, attributed and time-stamped. What happens next stays your lab’s call.

  6. 06
    Written as it happened

    New readings are appended to the on-slide record. Existing readings stay as they were recorded.

From slide to file

  1. ReadTap the label end to read the slide’s record in the app.
  2. ReviewFlagged steps come first. Add your note.
  3. ExportKeep the Prova Record with the case.

One slide. One day. One page your QA lead will want to read.

Illustrative record. Final format may change.

Read it

Your phone is the reader. Tap the label end. That’s it.

No separate reader to buy. Read S1 with a compatible phone and the Prova mobile app: hold it to the label end and the slide’s record opens.

Where it matters most

Start with the assays that carry the most weight.

Some results carry more weight in clinical interpretation. Those are the workflows to record first.

HER2, 0 or 1+

In 2023, ASCO and CAP called the distinction between HER2 IHC 0 and 1+ clinically relevant.1 A 2022 study of CAP survey data and a separate reader cohort reported low agreement at that same boundary.2

HER2 IHC

The call rests on faint, partial membrane staining, where small differences in a run can matter.

S1 recordsRetrieval heat and time, at the slide

HER2 Dual ISH

An equivocal IHC result can lead to reflex ISH testing, with its own denaturation and hybridization steps.

S1 recordsDenaturation and hybridization, start to finish

Prostate basal-cell cocktails

A small focus on a needle core is often confirmed on a single stained slide.

S1 recordsThe whole day of that one slide

FISH

The PathVysion protocol sets denaturation at 72 °C, give or take one degree, before hybridization.3

S1 recordsTemperature and time through denaturation

S1 doesn’t score a stain. It shows whether the slide had the day its protocol called for.

Also on the list: ER and PR, Ki-67, PD-L1, mismatch repair. Sources: Wolff AC et al., J Clin Oncol 2023; Fernandez AI et al., JAMA Oncol 2022; Abbott PathVysion package insert. Full references below.

Serial sections

Adjacent sections. Two processing histories.

These sections came from one block and followed different workflows, as IHC and ISH should. Each record shows the temperature and timing of its own journey, including how long each stayed in the dryer.

S1-0264 · HER2 IHC protocol S1-0265 · HER2 Dual ISH protocol 95 °C60 °C37 °C95 °C60 °C37 °C 49 min longer in the dryer than S1-0264 hybridizing at 44 °C 09:0010:0011:0012:0013:00
Illustrative profiles. Values are examples, not protocol specifications.

Cut minutes apart

Same block, same morning, adjacent sections.

Processed differently

Different protocols by design, and different waits by circumstance.

Now you can see it

Each slide brings its own record to the review.

A measured history. For every slide you run.

Every S1 adds to your lab’s record. It builds with every run, and it is evidence that images and logs can’t supply.

Built for the lab you already run

Designed to go where your slides go.

S1 keeps the standard 75 × 25 mm footprint and is designed for the baths, dryers, stainers, coverslippers and scanners you already use.

  1. Flotation bath Leica HI1210
  2. Slide dryer Thermo Scientific Heratherm
  3. Stainer Roche BenchMark ULTRA PLUS
  4. Coverslipper Leica CV5030
  5. Scanner Leica Aperio GT 450

One format. Many workflows.

  • Leica BOND‑PRIME
  • Leica BOND‑MAX
  • Agilent Dako Autostainer Link 48
  • Biocare ONCORE Pro
  • Epredia Lab Vision Autostainer 360
  • Leica HistoCore SPECTRA ST
  • Sakura Tissue‑Tek Prisma Plus
  • Leica ST5020 Multistainer
  • Thermo Scientific Heratherm OGS60
  • CellPath Mini Section Dryer
  • Leica Aperio GT 450
  • Hamamatsu NanoZoomer S360
  • Boekel Deluxe Lighted Tissue Flotation Bath
  • Leica CV5030
  • Roche VENTANA DP 200
  • 3DHISTECH Pannoramic 1000
  • Sakura Tissue‑Tek Film
  • Leica IP S
  • Epredia SlideMate AS
  • Epredia E1000 Dx
  • Grundium Ocus 40
  • Leica HistoCore CHROMAX ST
  • StatLab PiSmart S1
  • Milestone PRESTO PRO
  • Leica BOND‑III
  • Agilent Dako Omnis 165 Duo
  • Sakura Tissue‑Tek Genie
  • Biocare intelliPATH+
  • Roche VENTANA HE 600
  • Leica HistoCore SPECTRA CV
  • Epredia Gemini AS
  • ZEISS Axioscan 7
  • CellPath High Capacity Section Dryer
  • Agilent Dako Artisan Link Pro
  • Leica Aperio AT2
  • Leica HistoCore Water Bath M
  • Epredia Digital Paraffin Flotation Bath
  • Philips IntelliSite SG300
  • Roche VENTANA DP 600
  • Sakura Tissue‑Tek Glas g2
  • Epredia ClearVue
  • Epredia SlideMate Laser
  • Primera Signature
  • Motic EasyScan Infinity 100
  • Huron TissueScope iQ
  • Leica HistoCore CHROMAX CV
  • Sakura Tissue‑Tek SmartWrite

S1 keeps the 75 × 25 mm footprint. No platform is validated yet. Compatibility is validated platform by platform.

In the box

Thirty to a carton. Asleep until needed.

The planned Prova S1 production carton, closed. As you scroll, the box slides off, two violet seals peel away, the grey mold lifts out, and a phone runs along the tray's rim while each of the thirty slides lights in turn.
  1. Slide the box off.

    Thirty S1 slides inside, sealed and asleep.

  2. Peel the two violet seals.

    Half on the mold, half on the rim. Pull both tabs.

  3. Lift the mold.

    It holds every slide still and keeps dust out on the way to your lab.

  4. Your phone awakens the slides.

    Run it along the rim. Each slide lights as its record starts.

  5. Thirty awake. Thirty records.

    Load them where your slides already go.

The planned 30-slide production carton. Slides stand label end up, ready to scan and lift out, like the racks you use today.

Renders. Packaging and app screens may change before release.

Quick start

Carton to record. The planned workflow, in five steps.

  1. 01Open

    Slide the box off, peel the two violet seals and lift the mold.

  2. 02Wake

    Open the Prova mobile app and run your phone along the rim of the tray. The app wakes each slide, and its seam lights as recording starts.

  3. 03Mount

    Pick up your section the way you always do. The record is already running.

  4. 04Run

    Bake, stain, coverslip and scan on the instruments you use today. S1 travels with its section.

  5. 05Read

    Hold the top of your phone to the label end. The slide’s whole day opens in the app.

Planned use. Steps may be refined before release.

In your space

Set the tray on your bench. Thirty slides, at true size.

Turn it here, or place it on your bench in AR and walk around it. Every seam lit, every slot numbered.

See it on your bench.Scan with your iPhone or Android phone to place the tray at true size.

Answers

Good questions. Straight answers.

Can we order S1 today?
Not yet. Reserve it free, with no obligation to order, and we’ll contact you before the first production run.
How do we get an S1 demo kit?
Order Prova V1, through your Cardinal Health representative or direct. One complimentary S1 demo kit per lab is included and ships when S1 is available.
Does S1 replace V1?
No. V1 verifies your BenchMark heating pads every 90 days. S1 records each slide on every run in between.
Does S1 change our protocols?
No. S1 rides along with your section, on the instruments you already run.
What does the record tell us?
The heat, time and handling a slide went through, step by step. It doesn’t interpret a stain or make a diagnosis.

S1 at a glance

Size
75 × 25 mm
Records
Temperature, time, movement and impacts
Reads with
A compatible phone and the Prova app
Memory
On the slide, append-only
Packaging
30 slides to a carton
Status
Reservations open

Prova S1 is not yet for sale. In development. Planned capabilities; performance and instrument compatibility require validation.

Free reservation

Be first in line.

Reserve S1 for your lab. It’s free, with no obligation to order. We’ll contact you before the first production run.

Your role
Slides processed per month
When would you like to evaluate S1? Optional

We’ll only use these details to contact you about S1.

Proof for every patient.

The example. Slide S1-0264, its case, readings, limits and review notes are illustrative. They show a planned workflow, not a customer result. S1 records, app screens, values and scenarios on this page are illustrative.

The product. Prova S1 is not yet for sale. In development. Capabilities are planned, and performance and instrument compatibility require validation. Reservations are free and are not orders.

The record. S1 records processing conditions. It does not score a stain or make a diagnosis.

  1. Wolff AC, Somerfield MR, Dowsett M, et al. Human Epidermal Growth Factor Receptor 2 Testing in Breast Cancer: ASCO–College of American Pathologists Guideline Update. J Clin Oncol. 2023;41(22):3867-3872.
  2. Fernandez AI, Liu M, Bellizzi A, et al. Examination of Low ERBB2 Protein Expression in Breast Cancer Tissue. JAMA Oncol. 2022;8(4):607-610.
  3. Abbott Molecular. PathVysion HER-2 DNA Probe Kit package insert.

AR viewing needs a recent iPhone, iPad or ARCore Android device. Instrument names are trademarks of their respective owners. Prova is not affiliated with or endorsed by them.